Rotary_Switch_Module_V1__SKU_SEN0156_-DFRobot

SKU:SEN0156

Introduction

A rotary switch is a switch operated by rotation. These are often chosen when more than 2 positions are needed, such as multi-speed control. The Rotary Switch uses an analog input to read the 12 state which saves IO resource for the Arduino. This Rotary Switch Module has most 12 position. Each position has the approprite indicator.You can also adjust metal buckle inside the switch to change position number.So, it's very flexible for you to use.

A rotary switch consists of a spindle or "rotor" that has a contact arm or "spoke" which projects from its surface like a cam. It has an array of terminals, arranged in a circle around the rotor, each of which serves as a contact for the "spoke" through which any one of a number of different electrical circuits can be connected to the rotor. Thus a rotary switch provides greater pole and throw capabilities than simpler switches do.

Specifications

How to Change Position Number

Regulating metal buckle among differrnt fixing hole can change position number.

2.png

Wiring Diagram

Rotary_Switch_Module_Connection_Diagram1.png

Sample Code 1

int sensorvalue;

void setup(){
    Serial.begin(9600);
}
void loop(){
    sensorvalue = analogRead(0);            // read value from different position
    Serial.println(sensorvalue);
    delay(200);
}

Sample Code 2

The same position value of each switch is different.So, by sample code 1, the each position value can be read, and modify the appropriate reference value in the following code.

/*
 # This Sample code is reading Switch position.
 */
int adc_key_val[12] ={630,680,750,810,845,860,890,905,920,940,950,980};
int NUM_KEYS = 12;
int adc_key_in;
int key=-1;
int oldkey=-1;
void setup()
{
  Serial.begin(9600);                   // 9600 bps
}
void loop()
{
  adc_key_in = analogRead(0);            // read the value from the sensor
  key = get_key(adc_key_in);             // convert into position
  if (key != oldkey)                     // if a position is detected
   {
    delay(50);  // wait for debounce time
    adc_key_in = analogRead(0);          // read the value from the sensor
    key = get_key(adc_key_in);           //convert into position
    if (key != oldkey)
    {
      oldkey = key;
      if (key >=0){
        switch(key)
        {
           case 0:Serial.println("S1 OK");
                  break;
           case 1:Serial.println("S2 OK");
                  break;
           case 2:Serial.println("S3 OK");
                  break;
           case 3:Serial.println("S4 OK");
                  break;
           case 4:Serial.println("S5 OK");
                  break;
           case 5:Serial.println("S6 OK");
                  break;
           case 6:Serial.println("S7 OK");
                  break;
           case 7:Serial.println("S8 OK");
                  break;
           case 8:Serial.println("S9 OK");
                  break;
           case 9:Serial.println("S10 OK");
                   break;
           case 10:Serial.println("S11 OK");
                  break;
           case 11:Serial.println("S12 OK");
                  break;
        }
      }
    }
  }
 delay(100);
}
// Convert ADC value to key number
int get_key(unsigned int input)
{
    int k;
    for (k = 0; k < NUM_KEYS; k++)
    {
      if (input < adc_key_val[k])
     {
            return k;
        }
   }
       if (k >= NUM_KEYS)k = -1;
       return k;
}

FAQ

For any questions, advice or cool ideas to share, please visit the DFRobot Forum.