Forum >Problem with Bluno - BLE with Arduino Uno.
Problem with Bluno - BLE with Arduino Uno.
AlessioG 2014-09-12 03:27:05 15424 Views29 Replies Hello I've bought a wonderful Bluno - BLE with Arduino Uno DFR0267.
my goal is to replicate this video.
[url=https://www.youtube.com/watch?v=6o_QVlltNgM]https://www.youtube.com/watch?v=6o_QVlltNgM[/url]
The problem is when I try to find the bluetooth of the BLUNO I can't find it.
I tried with my phone a Doogee Collo D120 and scanning with my PC an Elitebook 2540p but the bluetooth mac address of the Bluno isn't available.
Please could u help me?
Kind Regards.
my goal is to replicate this video.
[url=https://www.youtube.com/watch?v=6o_QVlltNgM]https://www.youtube.com/watch?v=6o_QVlltNgM[/url]
The problem is when I try to find the bluetooth of the BLUNO I can't find it.
I tried with my phone a Doogee Collo D120 and scanning with my PC an Elitebook 2540p but the bluetooth mac address of the Bluno isn't available.
Please could u help me?
Kind Regards.
2014-09-20 02:31:56 Hello,
Could you send AT Command "AT+SN=?" to check whether BLE has been locked? Grey.CC
Could you send AT Command "AT+SN=?" to check whether BLE has been locked?
Grey.CC 2014-09-20 02:31:56 Hello,
Could you send AT Command "AT+SN=?" to check whether BLE has been locked? Grey.CC
Could you send AT Command "AT+SN=?" to check whether BLE has been locked?
Grey.CC 2014-09-20 02:31:56 Hello,
Could you send AT Command "AT+SN=?" to check whether BLE has been locked? Grey.CC
Could you send AT Command "AT+SN=?" to check whether BLE has been locked?
Grey.CC 2014-09-19 09:31:40 After my upgrade no. Before the upgrade yes (and thus I did the upgrade to 1.8version of the firmware as the step-by-step guide says).
However, still I can access the serial port through IDE and give AT commands to the chip.
KYR.
kyriakos
However, still I can access the serial port through IDE and give AT commands to the chip.
KYR.
kyriakos 2014-09-19 09:31:40 After my upgrade no. Before the upgrade yes (and thus I did the upgrade to 1.8version of the firmware as the step-by-step guide says).
However, still I can access the serial port through IDE and give AT commands to the chip.
KYR.
kyriakos
However, still I can access the serial port through IDE and give AT commands to the chip.
KYR.
kyriakos 2014-09-19 09:31:40 After my upgrade no. Before the upgrade yes (and thus I did the upgrade to 1.8version of the firmware as the step-by-step guide says).
However, still I can access the serial port through IDE and give AT commands to the chip.
KYR.
kyriakos
However, still I can access the serial port through IDE and give AT commands to the chip.
KYR.
kyriakos 2014-09-18 21:47:35 I mean press "Boot" and plug usb cable. They should be flashing,
And does anything appear in the Device Manager?
Grey.CC
And does anything appear in the Device Manager?
Grey.CC 2014-09-18 21:47:35 I mean press "Boot" and plug usb cable. They should be flashing,
And does anything appear in the Device Manager?
Grey.CC
And does anything appear in the Device Manager?
Grey.CC 2014-09-18 21:47:35 I mean press "Boot" and plug usb cable. They should be flashing,
And does anything appear in the Device Manager?
Grey.CC
And does anything appear in the Device Manager?
Grey.CC 2014-09-17 21:33:06 Hi Grey,
when I press boot or reset, the link and pair LEDS do not blink. When I try to upload a sketch, they blink, but the sketch is not uploaded. it seems the path from bluetooth to Atmega chip is broken (?).
However I still can see the serial port from Arduino IDE and can change (through AT commands) the setting of the BLE chip). kyriakos
when I press boot or reset, the link and pair LEDS do not blink. When I try to upload a sketch, they blink, but the sketch is not uploaded. it seems the path from bluetooth to Atmega chip is broken (?).
However I still can see the serial port from Arduino IDE and can change (through AT commands) the setting of the BLE chip).
kyriakos 2014-09-17 21:33:06 Hi Grey,
when I press boot or reset, the link and pair LEDS do not blink. When I try to upload a sketch, they blink, but the sketch is not uploaded. it seems the path from bluetooth to Atmega chip is broken (?).
However I still can see the serial port from Arduino IDE and can change (through AT commands) the setting of the BLE chip). kyriakos
when I press boot or reset, the link and pair LEDS do not blink. When I try to upload a sketch, they blink, but the sketch is not uploaded. it seems the path from bluetooth to Atmega chip is broken (?).
However I still can see the serial port from Arduino IDE and can change (through AT commands) the setting of the BLE chip).
kyriakos 2014-09-17 21:33:06 Hi Grey,
when I press boot or reset, the link and pair LEDS do not blink. When I try to upload a sketch, they blink, but the sketch is not uploaded. it seems the path from bluetooth to Atmega chip is broken (?).
However I still can see the serial port from Arduino IDE and can change (through AT commands) the setting of the BLE chip). kyriakos
when I press boot or reset, the link and pair LEDS do not blink. When I try to upload a sketch, they blink, but the sketch is not uploaded. it seems the path from bluetooth to Atmega chip is broken (?).
However I still can see the serial port from Arduino IDE and can change (through AT commands) the setting of the BLE chip).
kyriakos 2014-09-15 18:20:44 When you press boot, whether LINK and Pair Leds are flashing?
Could you uninstall the bluno driver and install again? I am not sure whether it is driver issue. Grey.CC
Could you uninstall the bluno driver and install again? I am not sure whether it is driver issue.
Grey.CC 2014-09-15 18:20:44 When you press boot, whether LINK and Pair Leds are flashing?
Could you uninstall the bluno driver and install again? I am not sure whether it is driver issue. Grey.CC
Could you uninstall the bluno driver and install again? I am not sure whether it is driver issue.
Grey.CC 